2002 Ingersoll-Rand T3W -Water Well Drill, Day Cab, A/C, Heater, Caterpillar C-12 Engine, 380 Rated Horsepower, Eaton Fuller 13 Speed Manual Transmission, 228" Wheel Base, 17,000 lb. Capacity Front Axle, 35,000 lb. Capacity Rear Axles, 52,000 lb. GVWR.
T3W Drilling Rig, Open Operator Station, Caterpillar C-15 Engine, Rod Changer, Ingersoll-Rand HR 2.5 Engine Driven Compressor 900 CFM X 350 PSI, Kelly Drive System, Mileage: 62,137 KM, Has 3,644 Hours
No rod pipe or hammer with this drill

Location: SUDBURY, Ontario, Canada

2006 FOREMOST DR12
Detailed Description
Kenworth T800 carrier with 475HP Caterpillar C15 engine. 900/350 IR compressor. 4 1/2 inch rods and tooling.

Location: Donegal, Ireland

2007 REICHDRILL T650W II
2007 REICHDRILL T650W II- MACK 6x4 chassis with lifting axle, 950 CFM / 350 psi compressor. Cat deck engine. In super condition all round.

Location Saggart, DUBLIN, Ireland

2002-Schramm-T450
2002 INTERNATIONAL 4900 Truck and Rig is great condition.Breakout wrench go's out to 60".It aslo hasa rotation torque limiter and slow feed drill-up value. Has a jib boom hydraulic swing and extend. A lazy sussan 10 pipe breakout(3.5"odonly)stabilizer support bars. Foam injection, water injection 18gpm. All full walkways and junkboxs.

Location: USA / Mooresville, North Carolina
Serial Number J102-B222
Truck; International 4900 6*4 300hp

1996 SCHRAMM T450W For Sale, 410 hp, Spicer 11 spd
Air Compressor Information, Sullair 1000/350, 28.5 foot top head travel mast, 40,000 lb pullup. 16-1/2 inch table opening, 540 hp deck engine, 1000/350 air compressor with clutch. Sliding top head, 15,000 lb winch , 12 pipe 4-1/2 inch lazy susan carousel, Fuel saving variable speed cooling fan. Control Panel. DHT Lubricator and set up for 4.5 x 20 foot drill pipe. 815/350, Detroit 8V92, 30,000# pullback, Bean Pump, oiler.

1996 SCHRAMM T450W For Sale
Location: USA / Honesdale, Pennsylvania

2008 SCHRAMM T685WS-D MOUNTED ON 2009 STERLING WITH 7,535 MILE AND ONLY 1629 HRS.
HAS 1350/500 SULLAIR AIR COMPRESSOR AND 2000 SERIES DETROIT ENGINE 765HP., 35 GPM WATER INJECTION, Serial Number J125-2009 , HYDRAULIC FOR MUD PUMP, SINGLE ROD LOADER. 1000 PSI PIPING

1350cfm/500psi SULLAIR AIR COMPRESSOR AND 2000 SERIES DETROIT ENGINE 765HP

Location : USA / HERRINGTON, Kansas

2008 Atlas Copco T4W - 1250/350 Compressor, QSK19 Cummins Deck Engine. Approx. 2,000 Hrs., 70K LB Pullback, Worm Gearhead, Compressor Clutch Assembly, 7 & 4 Rod Carousels, (3) Hyd. Jacks, Double Jib Booms, Pullmaster Rod Handling Winch, 25 GPM Bean Inj. Pump, Hammer Oiler, All Hand Tools, 2,400' Of 4 1/2" X 3 31/2" Drill Pipe, Many Spare Parts, Hoses, Gauges, Proheat Pre-Heater, Detroit Locker Package. Mounted On 2008 CCC, w/ 400 HP Cat. Excellent Condition. 1250/350 Compressor, Cummins Deck Engine. Approx. 2K Hrs, 70K LB Pullback, 25 GPM Bean Inj. Pump . Price - $675,000.00

Location: USA / Miami, Florida

1995 INGERSOLL-RAND T3W For Sale- Waterwell Drill Rigs - IR T3W HR2, CAT 3406B Engine, Water Cooling System, Wheeled, Enclosed Cab...
Chained Feed Mechanism, Professionally re-sprayed with marine grade paint, compressor reconditioned by Ingersoll Rand & warranted for 12 months, 900CFM x 350PSI, Caterpillar deck engine, 21 x 20ft 4.5" drill rods, 2 x 6" Hammers, fully checked over and ready for work. Chassis: Ford L9000 Delux with 30,000 miles, 8 Speed splitter box, tyres 50% all round, cummins engine. In perfect visual & mechanical condition.

Location: Saggart, Dublin, Ireland

2005 REICHDRILL T-650W11, (1920 HOURS ON RIG)
IT'S MOUNTED ON CVB713 GRANITE 6 X 4, WITH MACK 460 HORSEPOWER AND MACK T318L 18 SPEED(5600 MILES ON MACK) 175 GALLON FUEL TANK MOUNTED ON TRUCK CHASSIS, SULLAIR 1000 CFM & 350 PSI COMPRESSOR WITH CAT 3406C 500 HP @ 2100 RPM
20 GPM WATER INJECTION PUMP, AUXILLARY REMOTE , CONTROLS(WIRELESS), AIR LINE LUBRICATOR - 8 GALLON CAPACITY, PKLATFORMS &
WALKWAY GROUP, FOLDING 2 - HAMMER HOLDRES -ONE - 6 IN. & ONE - 8 IN., 300' OF DRILL , ROD. THIS RIG IS LIKE NEW!

Location Fontana, California

Drilled Water wells
Drilled wells are smaller in diameter, usually ranging from 10-20 cm (4-8 in.), and completed to much greater depths than bored wells, up to several hundred metres. The producing aquifer is generally less susceptible to pollution from surface sources because of the depth. Also, the water supply tends to be more reliable since it is less affected by seasonal weather patterns.

There are two primary methods of drilling well for water:
- Rotary drilled wells by Rotary drilling rigs
- Cable tool drilled wells by smaller mobile drilling rigs

Rotary drilled wells are constructed using a drill bit on the end of a rotating drillstem. Drilling fluid or air is circulated down through the drillstem in the hole and back to the surface to remove cuttings. Rotary drilling rigs operate quickly and can reach depths of over 300 m (1000 ft.), with casing diameters of 10-45 cm (4-18 in.).

Cable tool drilled wells are constructed by lifting and dropping a heavy drill bit in the bore hole. The resulting loose material, mixed with water, is removed using a bailer or sand pump. This method, also called percussion drilling, reaches depths up to 300 m (1000 ft.). Well diameters can range from 10-45 cm (4-18 in.). The drilling rate is typically much slower than for a rotary rig, but when aquifers are low yielding, they may be more easily identified using this method.